Update the list of PS keys

1 files changed, 802 insertions, 0 deletions

diff --git a/tools/csr.c b/tools/csr.c
index 43ae25b0..556f13cb 100644
--- a/tools/csr.c
+++ b/tools/csr.c
@@ -424,38 +424,840 @@ char *csr_pskeytostr(uint16_t pskey)
 		return "Maximum SCO links";
 	case CSR_PSKEY_MAX_REMOTE_MASTERS:
 		return "Maximum remote masters";
+	case CSR_PSKEY_ENABLE_MASTERY_WITH_SLAVERY:
+		return "Support master and slave roles simultaneously";
+	case CSR_PSKEY_H_HC_FC_MAX_ACL_PKT_LEN:
+		return "Maximum HCI ACL packet length";
+	case CSR_PSKEY_H_HC_FC_MAX_SCO_PKT_LEN:
+		return "Maximum HCI SCO packet length";
+	case CSR_PSKEY_H_HC_FC_MAX_ACL_PKTS:
+		return "Maximum number of HCI ACL packets";
+	case CSR_PSKEY_H_HC_FC_MAX_SCO_PKTS:
+		return "Maximum number of HCI SCO packets";
+	case CSR_PSKEY_LC_FC_BUFFER_LOW_WATER_MARK:
+		return "Flow control low water mark";
+	case CSR_PSKEY_LC_MAX_TX_POWER:
+		return "Maximum transmit power";
+	case CSR_PSKEY_TX_GAIN_RAMP:
+		return "Transmit gain ramp rate";
+	case CSR_PSKEY_LC_PEER_POWER_PERIOD:
+		return "Peer transmit power control interval";
+	case CSR_PSKEY_LC_FC_POOLS_LOW_WATER_MARK:
+		return "Flow control pool low water mark";
+	case CSR_PSKEY_LC_DEFAULT_TX_POWER:
+		return "Default transmit power";
+	case CSR_PSKEY_LC_RSSI_GOLDEN_RANGE:
+		return "RSSI at bottom of golden receive range";
+	case CSR_PSKEY_LC_COMBO_DISABLE_PIO_MASK:
+		return "Combo: PIO lines and logic to disable transmit";
+	case CSR_PSKEY_LC_COMBO_PRIORITY_PIO_MASK:
+		return "Combo: priority activity PIO lines and logic";
+	case CSR_PSKEY_LC_COMBO_DOT11_CHANNEL_PIO_BASE:
+		return "Combo: 802.11b channel number base PIO line";
+	case CSR_PSKEY_LC_COMBO_DOT11_BLOCK_CHANNELS:
+		return "Combo: channels to block either side of 802.11b";
+	case CSR_PSKEY_LC_MAX_TX_POWER_NO_RSSI:
+		return "Maximum transmit power when peer has no RSSI";
+	case CSR_PSKEY_LC_CONNECTION_RX_WINDOW:
+		return "Receive window size during connections";
+	case CSR_PSKEY_LC_COMBO_DOT11_TX_PROTECTION_MODE:
+		return "Combo: which TX packets shall we protect";
+	case CSR_PSKEY_LC_ENHANCED_POWER_TABLE:
+		return "Radio power table";
+	case CSR_PSKEY_LC_WIDEBAND_RSSI_CONFIG:
+		return "RSSI configuration for use with wideband RSSI";
+	case CSR_PSKEY_LC_COMBO_DOT11_PRIORITY_LEAD:
+		return "Combo: How much notice will we give the Combo Card";
+	case CSR_PSKEY_BT_CLOCK_INIT:
+		return "Initial value of Bluetooth clock";
+	case CSR_PSKEY_TX_MR_MOD_DELAY:
+		return "TX Mod delay";
+	case CSR_PSKEY_RX_MR_SYNC_TIMING:
+		return "RX MR Sync Timing";
+	case CSR_PSKEY_RX_MR_SYNC_CONFIG:
+		return "RX MR Sync Configuration";
+	case CSR_PSKEY_LC_LOST_SYNC_SLOTS:
+		return "Time in ms for lost sync in low power modes";
+	case CSR_PSKEY_RX_MR_SAMP_CONFIG:
+		return "RX MR Sync Configuration";
+	case CSR_PSKEY_AGC_HYST_LEVELS:
+		return "AGC hysteresis levels";
+	case CSR_PSKEY_RX_LEVEL_LOW_SIGNAL:
+		return "ANA_RX_LVL at low signal strengths";
+	case CSR_PSKEY_AGC_IQ_LVL_VALUES:
+		return "ANA_IQ_LVL values for AGC algorithmn";
+	case CSR_PSKEY_MR_FTRIM_OFFSET_12DB:
+		return "ANA_RX_FTRIM offset when using 12 dB IF atten ";
+	case CSR_PSKEY_MR_FTRIM_OFFSET_6DB:
+		return "ANA_RX_FTRIM offset when using 6 dB IF atten ";
+	case CSR_PSKEY_NO_CAL_ON_BOOT:
+		return "Do not calibrate radio on boot";
+	case CSR_PSKEY_RSSI_HI_TARGET:
+		return "RSSI high target";
+	case CSR_PSKEY_PREFERRED_MIN_ATTENUATION:
+		return "Preferred minimum attenuator setting";
+	case CSR_PSKEY_LC_COMBO_DOT11_PRIORITY_OVERRIDE:
+		return "Combo: Treat all packets as high priority";
+	case CSR_PSKEY_LC_MULTISLOT_HOLDOFF:
+		return "Time till single slot packets are used for resync";
+	case CSR_PSKEY_FREE_KEY_PIGEON_HOLE:
+		return "Link key store bitfield";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR0:
+		return "Bluetooth address + link key 0";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR1:
+		return "Bluetooth address + link key 1";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR2:
+		return "Bluetooth address + link key 2";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR3:
+		return "Bluetooth address + link key 3";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR4:
+		return "Bluetooth address + link key 4";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR5:
+		return "Bluetooth address + link key 5";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR6:
+		return "Bluetooth address + link key 6";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR7:
+		return "Bluetooth address + link key 7";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR8:
+		return "Bluetooth address + link key 8";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR9:
+		return "Bluetooth address + link key 9";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR10:
+		return "Bluetooth address + link key 10";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR11:
+		return "Bluetooth address + link key 11";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR12:
+		return "Bluetooth address + link key 12";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR13:
+		return "Bluetooth address + link key 13";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR14:
+		return "Bluetooth address + link key 14";
+	case CSR_PSKEY_LINK_KEY_BD_ADDR15:
+		return "Bluetooth address + link key 15";
 	case CSR_PSKEY_ENC_KEY_LMIN:
 		return "Minimum encryption key length";
 	case CSR_PSKEY_ENC_KEY_LMAX:
 		return "Maximum encryption key length";
 	case CSR_PSKEY_LOCAL_SUPPORTED_FEATURES:
 		return "Local supported features block";
+	case CSR_PSKEY_LM_USE_UNIT_KEY:
+		return "Allow use of unit key for authentication?";
+	case CSR_PSKEY_HCI_NOP_DISABLE:
+		return "Disable the HCI Command_Status event on boot";
+	case CSR_PSKEY_LM_MAX_EVENT_FILTERS:
+		return "Maximum number of event filters";
+	case CSR_PSKEY_LM_TEST_SEND_ACCEPTED_TWICE:
+		return "LM sends two LMP_accepted messages in test mode";
+	case CSR_PSKEY_LM_MAX_PAGE_HOLD_TIME:
+		return "Maximum time we hold a device around page";
+	case CSR_PSKEY_AFH_ADAPTATION_RESPONSE_TIME:
+		return "LM period for AFH adaption";
+	case CSR_PSKEY_AFH_OPTIONS:
+		return "Options to configure AFH";
+	case CSR_PSKEY_AFH_RSSI_RUN_PERIOD:
+		return "AFH RSSI reading period";
+	case CSR_PSKEY_AFH_REENABLE_CHANNEL_TIME:
+		return "AFH good channel adding time";
+	case CSR_PSKEY_NO_DROP_ON_ACR_MS_FAIL:
+		return "Complete link if acr barge-in role switch refused";
+	case CSR_PSKEY_MAX_PRIVATE_KEYS:
+		return "Max private link keys stored";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR0:
+		return "Bluetooth address + link key 0";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR1:
+		return "Bluetooth address + link key 1";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR2:
+		return "Bluetooth address + link key 2";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR3:
+		return "Bluetooth address + link key 3";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR4:
+		return "Bluetooth address + link key 4";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR5:
+		return "Bluetooth address + link key 5";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR6:
+		return "Bluetooth address + link key 6";
+	case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR7:
+		return "Bluetooth address + link key 7";
 	case CSR_PSKEY_LOCAL_SUPPORTED_COMMANDS:
 		return "Local supported commands";
+	case CSR_PSKEY_LM_MAX_ABSENCE_INDEX:
+		return "Maximum absence index allowed";
+	case CSR_PSKEY_DEVICE_NAME:
+		return "Local device's \"user friendly\" name";
+	case CSR_PSKEY_AFH_RSSI_THRESHOLD:
+		return "AFH RSSI threshold";
+	case CSR_PSKEY_LM_CASUAL_SCAN_INTERVAL:
+		return "Scan interval in slots for casual scanning";
+	case CSR_PSKEY_AFH_MIN_MAP_CHANGE:
+		return "The minimum amount to change an AFH map by";
+	case CSR_PSKEY_AFH_RSSI_LP_RUN_PERIOD:
+		return "AFH RSSI reading period when in low power mode";
 	case CSR_PSKEY_HCI_LMP_LOCAL_VERSION:
 		return "The HCI and LMP version reported locally";
 	case CSR_PSKEY_LMP_REMOTE_VERSION:
 		return "The LMP version reported remotely";
+	case CSR_PSKEY_HOLD_ERROR_MESSAGE_NUMBER:
+		return "Maximum number of queued HCI Hardware Error Events";
+	case CSR_PSKEY_DFU_ATTRIBUTES:
+		return "DFU attributes";
+	case CSR_PSKEY_DFU_DETACH_TO:
+		return "DFU detach timeout";
+	case CSR_PSKEY_DFU_TRANSFER_SIZE:
+		return "DFU transfer size";
+	case CSR_PSKEY_DFU_ENABLE:
+		return "DFU enable";
+	case CSR_PSKEY_DFU_LIN_REG_ENABLE:
+		return "Linear Regulator enabled at boot in DFU mode";
+	case CSR_PSKEY_DFUENC_VMAPP_PK_MODULUS_MSB:
+		return "DFU encryption VM application public key MSB";
+	case CSR_PSKEY_DFUENC_VMAPP_PK_MODULUS_LSB:
+		return "DFU encryption VM application public key LSB";
+	case CSR_PSKEY_DFUENC_VMAPP_PK_M_DASH:
+		return "DFU encryption VM application M dash";
+	case CSR_PSKEY_DFUENC_VMAPP_PK_R2N_MSB:
+		return "DFU encryption VM application public key R2N MSB";
+	case CSR_PSKEY_DFUENC_VMAPP_PK_R2N_LSB:
+		return "DFU encryption VM application public key R2N LSB";
+	case CSR_PSKEY_BCSP_LM_PS_BLOCK:
+		return "BCSP link establishment block";
+	case CSR_PSKEY_HOSTIO_FC_PS_BLOCK:
+		return "HCI flow control block";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO0:
+		return "Host transport channel 0 settings (BCSP ACK";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO1:
+		return "Host transport channel 1 settings (BCSP-LE";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO2:
+		return "Host transport channel 2 settings (BCCMD";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO3:
+		return "Host transport channel 3 settings (HQ";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO4:
+		return "Host transport channel 4 settings (DM";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO5:
+		return "Host transport channel 5 settings (HCI CMD/EVT";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO6:
+		return "Host transport channel 6 settings (HCI ACL";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO7:
+		return "Host transport channel 7 settings (HCI SCO";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO8:
+		return "Host transport channel 8 settings (L2CAP";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO9:
+		return "Host transport channel 9 settings (RFCOMM";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO10:
+		return "Host transport channel 10 settings (SDP";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO11:
+		return "Host transport channel 11 settings (TEST";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO12:
+		return "Host transport channel 12 settings (DFU";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO13:
+		return "Host transport channel 13 settings (VM";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO14:
+		return "Host transport channel 14 settings";
+	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO15:
+		return "Host transport channel 15 settings";
+	case CSR_PSKEY_HOSTIO_UART_RESET_TIMEOUT:
+		return "UART reset counter timeout";
 	case CSR_PSKEY_HOSTIO_USE_HCI_EXTN:
 		return "Use hci_extn to route non-hci channels";
+	case CSR_PSKEY_HOSTIO_USE_HCI_EXTN_CCFC:
+		return "Use command-complete flow control for hci_extn";
+	case CSR_PSKEY_HOSTIO_HCI_EXTN_PAYLOAD_SIZE:
+		return "Maximum hci_extn payload size";
+	case CSR_PSKEY_BCSP_LM_CNF_CNT_LIMIT:
+		return "BCSP link establishment conf message count";
 	case CSR_PSKEY_HOSTIO_MAP_SCO_PCM:
 		return "Map SCO over PCM";
+	case CSR_PSKEY_HOSTIO_AWKWARD_PCM_SYNC:
+		return "PCM interface synchronisation is difficult";
+	case CSR_PSKEY_HOSTIO_BREAK_POLL_PERIOD:
+		return "Break poll period (microseconds";
+	case CSR_PSKEY_HOSTIO_MIN_UART_HCI_SCO_SIZE:
+		return "Minimum SCO packet size sent to host over UART HCI";
+	case CSR_PSKEY_HOSTIO_MAP_SCO_CODEC:
+		return "Map SCO over the built-in codec";
+	case CSR_PSKEY_PCM_CVSD_TX_HI_FREQ_BOOST:
+		return "High frequency boost for PCM when transmitting CVSD";
+	case CSR_PSKEY_PCM_CVSD_RX_HI_FREQ_BOOST:
+		return "High frequency boost for PCM when receiving CVSD";
+	case CSR_PSKEY_PCM_CONFIG32:
+		return "PCM interface settings bitfields";
+	case CSR_PSKEY_USE_OLD_BCSP_LE:
+		return "Use the old version of BCSP link establishment";
+	case CSR_PSKEY_PCM_CVSD_USE_NEW_FILTER:
+		return "CVSD uses the new filter if available";
+	case CSR_PSKEY_PCM_FORMAT:
+		return "PCM data format";
+	case CSR_PSKEY_CODEC_OUT_GAIN:
+		return "Audio output gain when using built-in codec";
+	case CSR_PSKEY_CODEC_IN_GAIN:
+		return "Audio input gain when using built-in codec";
+	case CSR_PSKEY_CODEC_PIO:
+		return "PIO to enable when built-in codec is enabled";
+	case CSR_PSKEY_PCM_LOW_JITTER_CONFIG:
+		return "PCM interface settings for low jitter master mode";
+	case CSR_PSKEY_HOSTIO_SCO_PCM_THRESHOLDS:
+		return "Thresholds for SCO PCM buffers";
+	case CSR_PSKEY_HOSTIO_SCO_HCI_THRESHOLDS:
+		return "Thresholds for SCO HCI buffers";
+	case CSR_PSKEY_HOSTIO_MAP_SCO_PCM_SLOT:
+		return "Route SCO data to specified slot in pcm frame";
 	case CSR_PSKEY_UART_BAUDRATE:
 		return "UART Baud rate";
+	case CSR_PSKEY_UART_CONFIG_BCSP:
+		return "UART configuration when using BCSP";
+	case CSR_PSKEY_UART_CONFIG_H4:
+		return "UART configuration when using H4";
+	case CSR_PSKEY_UART_CONFIG_H5:
+		return "UART configuration when using H5";
+	case CSR_PSKEY_UART_CONFIG_USR:
+		return "UART configuration when under VM control";
+	case CSR_PSKEY_UART_TX_CRCS:
+		return "Use CRCs for BCSP or H5";
+	case CSR_PSKEY_UART_ACK_TIMEOUT:
+		return "Acknowledgement timeout for BCSP and H5";
+	case CSR_PSKEY_UART_TX_MAX_ATTEMPTS:
+		return "Max times to send reliable BCSP or H5 message";
+	case CSR_PSKEY_UART_TX_WINDOW_SIZE:
+		return "Transmit window size for BCSP and H5";
+	case CSR_PSKEY_UART_HOST_WAKE:
+		return "UART host wakeup";
+	case CSR_PSKEY_HOSTIO_THROTTLE_TIMEOUT:
+		return "Host interface performance control.";
+	case CSR_PSKEY_PCM_ALWAYS_ENABLE:
+		return "PCM port is always enable when chip is running";
+	case CSR_PSKEY_UART_HOST_WAKE_SIGNAL:
+		return "Signal to use for uart host wakeup protocol";
+	case CSR_PSKEY_UART_CONFIG_H4DS:
+		return "UART configuration when using H4DS";
+	case CSR_PSKEY_H4DS_WAKE_DURATION:
+		return "How long to spend waking the host when using H4DS";
+	case CSR_PSKEY_H4DS_MAXWU:
+		return "Maximum number of H4DS Wake-Up messages to send";
+	case CSR_PSKEY_H4DS_LE_TIMER_PERIOD:
+		return "H4DS Link Establishment Tsync and Tconf period";
+	case CSR_PSKEY_H4DS_TWU_TIMER_PERIOD:
+		return "H4DS Twu timer period";
+	case CSR_PSKEY_H4DS_UART_IDLE_TIMER_PERIOD:
+		return "H4DS Tuart_idle timer period";
 	case CSR_PSKEY_ANA_FTRIM:
 		return "Crystal frequency trim";
+	case CSR_PSKEY_WD_TIMEOUT:
+		return "Watchdog timeout (microseconds";
+	case CSR_PSKEY_WD_PERIOD:
+		return "Watchdog period (microseconds";
 	case CSR_PSKEY_HOST_INTERFACE:
 		return "Host interface";
+	case CSR_PSKEY_HQ_HOST_TIMEOUT:
+		return "HQ host command timeout";
+	case CSR_PSKEY_HQ_ACTIVE:
+		return "Enable host query task?";
+	case CSR_PSKEY_BCCMD_SECURITY_ACTIVE:
+		return "Enable configuration security";
 	case CSR_PSKEY_ANA_FREQ:
 		return "Crystal frequency";
+	case CSR_PSKEY_PIO_PROTECT_MASK:
+		return "Access to PIO pins";
+	case CSR_PSKEY_PMALLOC_SIZES:
+		return "pmalloc sizes array";
+	case CSR_PSKEY_UART_BAUD_RATE:
+		return "UART Baud rate (pre 18";
+	case CSR_PSKEY_UART_CONFIG:
+		return "UART configuration bitfield";
+	case CSR_PSKEY_STUB:
+		return "Stub";
+	case CSR_PSKEY_TXRX_PIO_CONTROL:
+		return "TX and RX PIO control";
+	case CSR_PSKEY_ANA_RX_LEVEL:
+		return "ANA_RX_LVL register initial value";
+	case CSR_PSKEY_ANA_RX_FTRIM:
+		return "ANA_RX_FTRIM register initial value";
+	case CSR_PSKEY_PSBC_DATA_VERSION:
+		return "Persistent store version";
+	case CSR_PSKEY_PCM0_ATTENUATION:
+		return "Volume control on PCM channel 0";
+	case CSR_PSKEY_LO_LVL_MAX:
+		return "Maximum value of LO level control register";
+	case CSR_PSKEY_LO_ADC_AMPL_MIN:
+		return "Minimum value of the LO amplitude measured on the ADC";
+	case CSR_PSKEY_LO_ADC_AMPL_MAX:
+		return "Maximum value of the LO amplitude measured on the ADC";
+	case CSR_PSKEY_IQ_TRIM_CHANNEL:
+		return "IQ calibration channel";
+	case CSR_PSKEY_IQ_TRIM_GAIN:
+		return "IQ calibration gain";
+	case CSR_PSKEY_TX_OFFSET_HALF_MHZ:
+		return "Transmit offset";
+	case CSR_PSKEY_GBL_MISC_ENABLES:
+		return "Global miscellaneous hardware enables";
+	case CSR_PSKEY_UART_SLEEP_TIMEOUT:
+		return "Time in ms to deep sleep if nothing received";
+	case CSR_PSKEY_DEEP_SLEEP_STATE:
+		return "Deep sleep state usage";
+	case CSR_PSKEY_IQ_ENABLE_PHASE_TRIM:
+		return "IQ phase enable";
+	case CSR_PSKEY_HCI_HANDLE_FREEZE_PERIOD:
+		return "Time for which HCI handle is frozen after link removal";
+	case CSR_PSKEY_MAX_FROZEN_HCI_HANDLES:
+		return "Maximum number of frozen HCI handles";
+	case CSR_PSKEY_PAGETABLE_DESTRUCTION_DELAY:
+		return "Delay from freezing buf handle to deleting page table";
+	case CSR_PSKEY_IQ_TRIM_PIO_SETTINGS:
+		return "IQ PIO settings";
+	case CSR_PSKEY_USE_EXTERNAL_CLOCK:
+		return "Device uses an external clock";
+	case CSR_PSKEY_DEEP_SLEEP_WAKE_CTS:
+		return "Exit deep sleep on CTS line activity";
+	case CSR_PSKEY_FC_HC2H_FLUSH_DELAY:
+		return "Delay from disconnect to flushing HC->H FC tokens";
+	case CSR_PSKEY_RX_HIGHSIDE:
+		return "Disable the HIGHSIDE bit in ANA_CONFIG";
+	case CSR_PSKEY_TX_PRE_LVL:
+		return "TX pre-amplifier level";
+	case CSR_PSKEY_RX_SINGLE_ENDED:
+		return "RX single ended";
+	case CSR_PSKEY_TX_FILTER_CONFIG:
+		return "TX filter configuration";
+	case CSR_PSKEY_CLOCK_REQUEST_ENABLE:
+		return "External clock request enable";
+	case CSR_PSKEY_RX_MIN_ATTEN:
+		return "Minimum attenuation allowed for receiver";
+	case CSR_PSKEY_XTAL_TARGET_AMPLITUDE:
+		return "Crystal target amplitude";
+	case CSR_PSKEY_PCM_MIN_CPU_CLOCK:
+		return "Minimum CPU clock speed with PCM port running";
+	case CSR_PSKEY_HOST_INTERFACE_PIO_USB:
+		return "USB host interface selection PIO line";
+	case CSR_PSKEY_CPU_IDLE_MODE:
+		return "CPU idle mode when radio is active";
+	case CSR_PSKEY_DEEP_SLEEP_CLEAR_RTS:
+		return "Deep sleep clears the UART RTS line";
+	case CSR_PSKEY_RF_RESONANCE_TRIM:
+		return "Frequency trim for IQ and LNA resonant circuits";
+	case CSR_PSKEY_DEEP_SLEEP_PIO_WAKE:
+		return "PIO line to wake the chip from deep sleep";
+	case CSR_PSKEY_DRAIN_BORE_TIMERS:
+		return "Energy consumption measurement settings";
+	case CSR_PSKEY_DRAIN_TX_POWER_BASE:
+		return "Energy consumption measurement settings";
+	case CSR_PSKEY_MODULE_ID:
+		return "Module serial number";
+	case CSR_PSKEY_MODULE_DESIGN:
+		return "Module design ID";
+	case CSR_PSKEY_MODULE_SECURITY_CODE:
+		return "Module security code";
+	case CSR_PSKEY_VM_DISABLE:
+		return "VM disable";
+	case CSR_PSKEY_MOD_MANUF0:
+		return "Module manufactuer data 0";
+	case CSR_PSKEY_MOD_MANUF1:
+		return "Module manufactuer data 1";
+	case CSR_PSKEY_MOD_MANUF2:
+		return "Module manufactuer data 2";
+	case CSR_PSKEY_MOD_MANUF3:
+		return "Module manufactuer data 3";
+	case CSR_PSKEY_MOD_MANUF4:
+		return "Module manufactuer data 4";
+	case CSR_PSKEY_MOD_MANUF5:
+		return "Module manufactuer data 5";
+	case CSR_PSKEY_MOD_MANUF6:
+		return "Module manufactuer data 6";
+	case CSR_PSKEY_MOD_MANUF7:
+		return "Module manufactuer data 7";
+	case CSR_PSKEY_MOD_MANUF8:
+		return "Module manufactuer data 8";
+	case CSR_PSKEY_MOD_MANUF9:
+		return "Module manufactuer data 9";
+	case CSR_PSKEY_DUT_VM_DISABLE:
+		return "VM disable when entering radiotest modes";
+	case CSR_PSKEY_USR0:
+		return "User configuration data 0";
+	case CSR_PSKEY_USR1:
+		return "User configuration data 1";
+	case CSR_PSKEY_USR2:
+		return "User configuration data 2";
+	case CSR_PSKEY_USR3:
+		return "User configuration data 3";
+	case CSR_PSKEY_USR4:
+		return "User configuration data 4";
+	case CSR_PSKEY_USR5:
+		return "User configuration data 5";
+	case CSR_PSKEY_USR6:
+		return "User configuration data 6";
+	case CSR_PSKEY_USR7:
+		return "User configuration data 7";
+	case CSR_PSKEY_USR8:
+		return "User configuration data 8";
+	case CSR_PSKEY_USR9:
+		return "User configuration data 9";
+	case CSR_PSKEY_USR10:
+		return "User configuration data 10";
+	case CSR_PSKEY_USR11:
+		return "User configuration data 11";
+	case CSR_PSKEY_USR12:
+		return "User configuration data 12";
+	case CSR_PSKEY_USR13:
+		return "User configuration data 13";
+	case CSR_PSKEY_USR14:
+		return "User configuration data 14";
+	case CSR_PSKEY_USR15:
+		return "User configuration data 15";
+	case CSR_PSKEY_USR16:
+		return "User configuration data 16";
+	case CSR_PSKEY_USR17:
+		return "User configuration data 17";
+	case CSR_PSKEY_USR18:
+		return "User configuration data 18";
+	case CSR_PSKEY_USR19:
+		return "User configuration data 19";
+	case CSR_PSKEY_USR20:
+		return "User configuration data 20";
+	case CSR_PSKEY_USR21:
+		return "User configuration data 21";
+	case CSR_PSKEY_USR22:
+		return "User configuration data 22";
+	case CSR_PSKEY_USR23:
+		return "User configuration data 23";
+	case CSR_PSKEY_USR24:
+		return "User configuration data 24";
+	case CSR_PSKEY_USR25:
+		return "User configuration data 25";
+	case CSR_PSKEY_USR26:
+		return "User configuration data 26";
+	case CSR_PSKEY_USR27:
+		return "User configuration data 27";
+	case CSR_PSKEY_USR28:
+		return "User configuration data 28";
+	case CSR_PSKEY_USR29:
+		return "User configuration data 29";
+	case CSR_PSKEY_USR30:
+		return "User configuration data 30";
+	case CSR_PSKEY_USR31:
+		return "User configuration data 31";
+	case CSR_PSKEY_USR32:
+		return "User configuration data 32";
+	case CSR_PSKEY_USR33:
+		return "User configuration data 33";
+	case CSR_PSKEY_USR34:
+		return "User configuration data 34";
+	case CSR_PSKEY_USR35:
+		return "User configuration data 35";
+	case CSR_PSKEY_USR36:
+		return "User configuration data 36";
+	case CSR_PSKEY_USR37:
+		return "User configuration data 37";
+	case CSR_PSKEY_USR38:
+		return "User configuration data 38";
+	case CSR_PSKEY_USR39:
+		return "User configuration data 39";
+	case CSR_PSKEY_USR40:
+		return "User configuration data 40";
+	case CSR_PSKEY_USR41:
+		return "User configuration data 41";
+	case CSR_PSKEY_USR42:
+		return "User configuration data 42";
+	case CSR_PSKEY_USR43:
+		return "User configuration data 43";
+	case CSR_PSKEY_USR44:
+		return "User configuration data 44";
+	case CSR_PSKEY_USR45:
+		return "User configuration data 45";
+	case CSR_PSKEY_USR46:
+		return "User configuration data 46";
+	case CSR_PSKEY_USR47:
+		return "User configuration data 47";
+	case CSR_PSKEY_USR48:
+		return "User configuration data 48";
+	case CSR_PSKEY_USR49:
+		return "User configuration data 49";
+	case CSR_PSKEY_USB_VERSION:
+		return "USB specification version number";
+	case CSR_PSKEY_USB_DEVICE_CLASS_CODES:
+		return "USB device class codes";
 	case CSR_PSKEY_USB_VENDOR_ID:
 		return "USB vendor identifier";
 	case CSR_PSKEY_USB_PRODUCT_ID:
 		return "USB product identifier";
+	case CSR_PSKEY_USB_MANUF_STRING:
+		return "USB manufacturer string";
+	case CSR_PSKEY_USB_PRODUCT_STRING:
+		return "USB product string";
+	case CSR_PSKEY_USB_SERIAL_NUMBER_STRING:
+		return "USB serial number string";
+	case CSR_PSKEY_USB_CONFIG_STRING:
+		return "USB configuration string";
+	case CSR_PSKEY_USB_ATTRIBUTES:
+		return "USB attributes bitmap";
+	case CSR_PSKEY_USB_MAX_POWER:
+		return "USB device maximum power consumption";
+	case CSR_PSKEY_USB_BT_IF_CLASS_CODES:
+		return "USB Bluetooth interface class codes";
+	case CSR_PSKEY_USB_LANGID:
+		return "USB language strings supported";
+	case CSR_PSKEY_USB_DFU_CLASS_CODES:
+		return "USB DFU class codes block";
 	case CSR_PSKEY_USB_DFU_PRODUCT_ID:
 		return "USB DFU product ID";
+	case CSR_PSKEY_USB_PIO_DETACH:
+		return "USB detach/attach PIO line";
+	case CSR_PSKEY_USB_PIO_WAKEUP:
+		return "USB wakeup PIO line";
+	case CSR_PSKEY_USB_PIO_PULLUP:
+		return "USB D+ pullup PIO line";
+	case CSR_PSKEY_USB_PIO_VBUS:
+		return "USB VBus detection PIO Line";
+	case CSR_PSKEY_USB_PIO_WAKE_TIMEOUT:
+		return "Timeout for assertion of USB PIO wake signal";
+	case CSR_PSKEY_USB_PIO_RESUME:
+		return "PIO signal used in place of bus resume";
+	case CSR_PSKEY_USB_BT_SCO_IF_CLASS_CODES:
+		return "USB Bluetooth SCO interface class codes";
+	case CSR_PSKEY_USB_SUSPEND_PIO_LEVEL:
+		return "USB PIO levels to set when suspended";
+	case CSR_PSKEY_USB_SUSPEND_PIO_DIR:
+		return "USB PIO I/O directions to set when suspended";
+	case CSR_PSKEY_USB_SUSPEND_PIO_MASK:
+		return "USB PIO lines to be set forcibly in suspend";
+	case CSR_PSKEY_USB_ENDPOINT_0_MAX_PACKET_SIZE:
+		return "The maxmimum packet size for USB endpoint 0";
+	case CSR_PSKEY_USB_CONFIG:
+		return "USB config params for new chips (>bc2";
+	case CSR_PSKEY_RADIOTEST_ATTEN_INIT:
+		return "Radio test initial attenuator";
+	case CSR_PSKEY_RADIOTEST_FIRST_TRIM_TIME:
+		return "IQ first calibration period in test";
+	case CSR_PSKEY_RADIOTEST_SUBSEQUENT_TRIM_TIME:
+		return "IQ subsequent calibration period in test";
+	case CSR_PSKEY_RADIOTEST_LO_LVL_TRIM_ENABLE:
+		return "LO_LVL calibration enable";
+	case CSR_PSKEY_RADIOTEST_DISABLE_MODULATION:
+		return "Disable modulation during radiotest transmissions";
+	case CSR_PSKEY_RFCOMM_FCON_THRESHOLD:
+		return "RFCOMM aggregate flow control on threshold";
+	case CSR_PSKEY_RFCOMM_FCOFF_THRESHOLD:
+		return "RFCOMM aggregate flow control off threshold";
+	case CSR_PSKEY_IPV6_STATIC_ADDR:
+		return "Static IPv6 address";
+	case CSR_PSKEY_IPV4_STATIC_ADDR:
+		return "Static IPv4 address";
+	case CSR_PSKEY_IPV6_STATIC_PREFIX_LEN:
+		return "Static IPv6 prefix length";
+	case CSR_PSKEY_IPV6_STATIC_ROUTER_ADDR:
+		return "Static IPv6 router address";
+	case CSR_PSKEY_IPV4_STATIC_SUBNET_MASK:
+		return "Static IPv4 subnet mask";
+	case CSR_PSKEY_IPV4_STATIC_ROUTER_ADDR:
+		return "Static IPv4 router address";
+	case CSR_PSKEY_MDNS_NAME:
+		return "Multicast DNS name";
+	case CSR_PSKEY_FIXED_PIN:
+		return "Fixed PIN";
+	case CSR_PSKEY_MDNS_PORT:
+		return "Multicast DNS port";
+	case CSR_PSKEY_MDNS_TTL:
+		return "Multicast DNS TTL";
+	case CSR_PSKEY_MDNS_IPV4_ADDR:
+		return "Multicast DNS IPv4 address";
+	case CSR_PSKEY_ARP_CACHE_TIMEOUT:
+		return "ARP cache timeout";
+	case CSR_PSKEY_HFP_POWER_TABLE:
+		return "HFP power table";
+	case CSR_PSKEY_DRAIN_BORE_TIMER_COUNTERS:
+		return "Energy consumption estimation timer counters";
+	case CSR_PSKEY_DRAIN_BORE_COUNTERS:
+		return "Energy consumption estimation counters";
+	case CSR_PSKEY_LOOP_FILTER_TRIM:
+		return "Trim value to optimise loop filter";
+	case CSR_PSKEY_DRAIN_BORE_CURRENT_PEAK:
+		return "Energy consumption estimation current peak";
+	case CSR_PSKEY_FORCE_16MHZ_REF_PIO:
+		return "PIO line to force 16 MHz reference to be assumed";
+	case CSR_PSKEY_CDMA_LO_REF_LIMITS:
+		return "Local oscillator frequency reference limits for CDMA";
+	case CSR_PSKEY_CDMA_LO_ERROR_LIMITS:
+		return "Local oscillator frequency error limits for CDMA";
+	case CSR_PSKEY_CLOCK_STARTUP_DELAY:
+		return "Clock startup delay in milliseconds";
+	case CSR_PSKEY_DEEP_SLEEP_CORRECTION_FACTOR:
+		return "Deep sleep clock correction factor";
+	case CSR_PSKEY_TEMPERATURE_CALIBRATION:
+		return "Temperature in deg C for a given internal setting";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_INTERNAL_PA:
+		return "Temperature for given internal PA adjustment";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_PRE_LVL:
+		return "Temperature for a given TX_PRE_LVL adjustment";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_BB:
+		return "Temperature for a given TX_BB adjustment";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_ANA_FTRIM:
+		return "Temperature for given crystal trim adjustment";
+	case CSR_PSKEY_TEST_DELTA_OFFSET:
+		return "Frequency offset applied to synthesiser in test mode";
+	case CSR_PSKEY_RX_DYNAMIC_LVL_OFFSET:
+		return "Receiver dynamic level offset depending on channel";
+	case CSR_PSKEY_TEST_FORCE_OFFSET:
+		return "Force use of exact value in PSKEY_TEST_DELTA_OFFSET";
+	case CSR_PSKEY_RF_TRAP_BAD_DIVISION_RATIOS:
+		return "Trap bad division ratios in radio frequency tables";
+	case CSR_PSKEY_RADIOTEST_CDMA_LO_REF_LIMITS:
+		return "LO frequency reference limits for CDMA in radiotest";
 	case CSR_PSKEY_INITIAL_BOOTMODE:
 		return "Initial device bootmode";
+	case CSR_PSKEY_ONCHIP_HCI_CLIENT:
+		return "HCI traffic routed internally";
+	case CSR_PSKEY_RX_ATTEN_BACKOFF:
+		return "Receiver attenuation back-off";
+	case CSR_PSKEY_RX_ATTEN_UPDATE_RATE:
+		return "Receiver attenuation update rate";
+	case CSR_PSKEY_SYNTH_TXRX_THRESHOLDS:
+		return "Local oscillator tuning voltage limits for tx and rx";
+	case CSR_PSKEY_MIN_WAIT_STATES:
+		return "Flash wait state indicator";
+	case CSR_PSKEY_RSSI_CORRECTION:
+		return "RSSI correction factor.";
+	case CSR_PSKEY_SCHED_THROTTLE_TIMEOUT:
+		return "Scheduler performance control.";
+	case CSR_PSKEY_DEEP_SLEEP_USE_EXTERNAL_CLOCK:
+		return "Deep sleep uses external 32 kHz clock source";
+	case CSR_PSKEY_TRIM_RADIO_FILTERS:
+		return "Trim rx and tx radio filters if true.";
+	case CSR_PSKEY_TRANSMIT_OFFSET:
+		return "Transmit offset in units of 62.5 kHz";
+	case CSR_PSKEY_USB_VM_CONTROL:
+		return "VM application will supply USB descriptors";
+	case CSR_PSKEY_MR_ANA_RX_FTRIM:
+		return "Medium rate value for the ANA_RX_FTRIM register";
+	case CSR_PSKEY_I2C_CONFIG:
+		return "I2C configuration";
+	case CSR_PSKEY_MR_TX_FILTER_CONFIG:
+		return "TX filter configuration used for enhanced data rate";
+	case CSR_PSKEY_MR_TX_CONFIG2:
+		return "TX filter configuration used for enhanced data rate";
+	case CSR_PSKEY_USB_DONT_RESET_BOOTMODE_ON_HOST_RESET:
+		return "Don't reset bootmode if USB host resets";
+	case CSR_PSKEY_LC_USE_THROTTLING:
+		return "Adjust packet selection on packet error rate";
+	case CSR_PSKEY_CHARGER_TRIM:
+		return "Trim value for the current charger";
+	case CSR_PSKEY_CLOCK_REQUEST_FEATURES:
+		return "Clock request is tristated if enabled";
+	case CSR_PSKEY_TRANSMIT_OFFSET_CLASS1:
+		return "Transmit offset / 62.5 kHz for class 1 radios";
+	case CSR_PSKEY_TX_AVOID_PA_CLASS1_PIO:
+		return "PIO line asserted in class1 operation to avoid PA";
+	case CSR_PSKEY_MR_PIO_CONFIG:
+		return "PIO line asserted in class1 operation to avoid PA";
+	case CSR_PSKEY_UART_CONFIG2:
+		return "The UART Sampling point";
+	case CSR_PSKEY_CLASS1_IQ_LVL:
+		return "IQ demand level for class 1 power level";
+	case CSR_PSKEY_CLASS1_TX_CONFIG2:
+		return "TX filter configuration used for class 1 tx power";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_INTERNAL_PA_CLASS1:
+		return "Temperature for given internal PA adjustment";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_EXTERNAL_PA_CLASS1:
+		return "Temperature for given internal PA adjustment";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_PRE_LVL_MR:
+		return "Temperature adjustment for TX_PRE_LVL in EDR";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_BB_MR_HEADER:
+		return "Temperature for a given TX_BB in EDR header";
+	case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_BB_MR_PAYLOAD:
+		return "Temperature for a given TX_BB in EDR payload";
+	case CSR_PSKEY_RX_MR_EQ_TAPS:
+		return "Adjust receiver configuration for EDR";
+	case CSR_PSKEY_TX_PRE_LVL_CLASS1:
+		return "TX pre-amplifier level in class 1 operation";
+	case CSR_PSKEY_ANALOGUE_ATTENUATOR:
+		return "TX analogue attenuator setting";
+	case CSR_PSKEY_MR_RX_FILTER_TRIM:
+		return "Trim for receiver used in EDR.";
+	case CSR_PSKEY_MR_RX_FILTER_RESPONSE:
+		return "Filter response for receiver used in EDR.";
+	case CSR_PSKEY_PIO_WAKEUP_STATE:
+		return "PIO deep sleep wake up state ";
+	case CSR_PSKEY_MR_TX_IF_ATTEN_OFF_TEMP:
+		return "TX IF atten off temperature when using EDR.";
+	case CSR_PSKEY_LO_DIV_LATCH_BYPASS:
+		return "Bypass latch for LO dividers";
+	case CSR_PSKEY_LO_VCO_STANDBY:
+		return "Use standby mode for the LO VCO";
+	case CSR_PSKEY_SLOW_CLOCK_FILTER_SHIFT:
+		return "Slow clock sampling filter constant";
+	case CSR_PSKEY_SLOW_CLOCK_FILTER_DIVIDER:
+		return "Slow clock filter fractional threshold";
+	case CSR_PSKEY_USB_ATTRIBUTES_POWER:
+		return "USB self powered";
+	case CSR_PSKEY_USB_ATTRIBUTES_WAKEUP:
+		return "USB responds to wake-up";
+	case CSR_PSKEY_DFU_ATTRIBUTES_MANIFESTATION_TOLERANT:
+		return "DFU manifestation tolerant";
+	case CSR_PSKEY_DFU_ATTRIBUTES_CAN_UPLOAD:
+		return "DFU can upload";
+	case CSR_PSKEY_DFU_ATTRIBUTES_CAN_DOWNLOAD:
+		return "DFU can download";
+	case CSR_PSKEY_UART_CONFIG_STOP_BITS:
+		return "UART: stop bits";
+	case CSR_PSKEY_UART_CONFIG_PARITY_BIT:
+		return "UART: parity bit";
+	case CSR_PSKEY_UART_CONFIG_FLOW_CTRL_EN:
+		return "UART: hardware flow control";
+	case CSR_PSKEY_UART_CONFIG_RTS_AUTO_EN:
+		return "UART: RTS auto-enabled";
+	case CSR_PSKEY_UART_CONFIG_RTS:
+		return "UART: RTS asserted";
+	case CSR_PSKEY_UART_CONFIG_TX_ZERO_EN:
+		return "UART: TX zero enable";
+	case CSR_PSKEY_UART_CONFIG_NON_BCSP_EN:
+		return "UART: enable BCSP-specific hardware";
+	case CSR_PSKEY_UART_CONFIG_RX_RATE_DELAY:
+		return "UART: RX rate delay";
+	case CSR_PSKEY_UART_SEQ_TIMEOUT:
+		return "UART: BCSP ack timeout";
+	case CSR_PSKEY_UART_SEQ_RETRIES:
+		return "UART: retry limit in sequencing layer";
+	case CSR_PSKEY_UART_SEQ_WINSIZE:
+		return "UART: BCSP transmit window size";
+	case CSR_PSKEY_UART_USE_CRC_ON_TX:
+		return "UART: use BCSP CRCs";
+	case CSR_PSKEY_UART_HOST_INITIAL_STATE:
+		return "UART: initial host state";
+	case CSR_PSKEY_UART_HOST_ATTENTION_SPAN:
+		return "UART: host attention span";
+	case CSR_PSKEY_UART_HOST_WAKEUP_TIME:
+		return "UART: host wakeup time";
+	case CSR_PSKEY_UART_HOST_WAKEUP_WAIT:
+		return "UART: host wakeup wait";
+	case CSR_PSKEY_BCSP_LM_MODE:
+		return "BCSP link establishment mode";
+	case CSR_PSKEY_BCSP_LM_SYNC_RETRIES:
+		return "BCSP link establishment sync retries";
+	case CSR_PSKEY_BCSP_LM_TSHY:
+		return "BCSP link establishment Tshy";
+	case CSR_PSKEY_UART_DFU_CONFIG_STOP_BITS:
+		return "DFU mode UART: stop bits";
+	case CSR_PSKEY_UART_DFU_CONFIG_PARITY_BIT:
+		return "DFU mode UART: parity bit";
+	case CSR_PSKEY_UART_DFU_CONFIG_FLOW_CTRL_EN:
+		return "DFU mode UART: hardware flow control";
+	case CSR_PSKEY_UART_DFU_CONFIG_RTS_AUTO_EN:
+		return "DFU mode UART: RTS auto-enabled";
+	case CSR_PSKEY_UART_DFU_CONFIG_RTS:
+		return "DFU mode UART: RTS asserted";
+	case CSR_PSKEY_UART_DFU_CONFIG_TX_ZERO_EN:
+		return "DFU mode UART: TX zero enable";
+	case CSR_PSKEY_UART_DFU_CONFIG_NON_BCSP_EN:
+		return "DFU mode UART: enable BCSP-specific hardware";
+	case CSR_PSKEY_UART_DFU_CONFIG_RX_RATE_DELAY:
+		return "DFU mode UART: RX rate delay";
+	case CSR_PSKEY_AMUX_AIO0:
+		return "Multiplexer for AIO 0";
+	case CSR_PSKEY_AMUX_AIO1:
+		return "Multiplexer for AIO 1";
+	case CSR_PSKEY_AMUX_AIO2:
+		return "Multiplexer for AIO 2";
+	case CSR_PSKEY_AMUX_AIO3:
+		return "Multiplexer for AIO 3";
+	case CSR_PSKEY_LOCAL_NAME_SIMPLIFIED:
+		return "Local Name (simplified";
+	case CSR_PSKEY_EXTENDED_STUB:
+		return "Extended stub";
 	default:
 		return "Unknown";
 	}