1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
|
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify
# it under the terms of the GNU Lesser General Public License as
# published by the Free Software Foundation; either version 2.1 of the
# License, or (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, write to the Free Software Foundation,
# Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
; Common part of all paths
; So here's generally how mixer paths are used by PA: PA goes through
; a mixer path file from top to bottom and checks if a mixer element
; described therein exists. If so it is added to the list of mixer
; elements PA will control, keeping the order it read them in. If a
; mixer element described here has set the required= or
; required-absent= directives a path might not be accepted as valid
; and is ignored in its entirety (see below). However usually if a
; element listed here is missing this one element is ignored but not
; the entire path.
;
; When a device shall be muted/unmuted *all* elements listed in a path
; file with "switch = mute" will be toggled.
;
; When a device shall change its volume, PA will got through the list
; of all elements with "volume = merge" and set the volume on the
; first element. If that element does not support dB volumes, this is
; where the story ends. If it does support dB volumes, PA divides the
; requested volume by the volume that was set on this element, and
; then go on to the next element with "volume = merge" and then set
; that there, and so on. That way the first volume element in the
; path will be the one that does the 'biggest' part of the overall
; volume adjustment, with the remaining elements usually being set to
; some value next to 0dB. This logic makes sure we get the full range
; over all volume sliders and a very high granularity of volumes
; already in hardware.
;
; All switches and enumerations set to "select" are exposed via the
; "port" functionality of sinks/sources. Basically every possible
; switch setting and every possible enumeration setting will be
; combined and made into a "port". So make sure you don't list too
; many switches/enums for exposing, because the number of ports might
; rise exponentially.
;
; Only one path can be selected at a time. All paths that are valid
; for an audio device will be exposed as "port" for the sink/source.
; [General]
; priority = ... # Priority for this path
; description = ...
;
; [Option ...:...] # For each option of an enumeration or switch element
; # that shall be exposed as a sink/source port. Needs to
; # be named after the Element, followed by a colon, followed
; # by the option name, resp. on/off if the element is a switch.
; name = ... # Logical name to use in the path identifier
; priority = ... # Priority if this is made into a device port
;
; [Element ...] # For each element that we shall control
; required = ignore | switch | volume | enumeration | any # If set, require this element to be of this kind and available,
; # otherwise don't consider this path valid for the card
; required-absent = ignore | switch | volume # If set, require this element to not be of this kind and not
; # available, otherwise don't consider this path valid for the card
;
; switch = ignore | mute | off | on | select # What to do with this switch: ignore it, make it follow mute status,
; # always set it to off, always to on, or make it selectable as port.
; # If set to 'select' you need to define an Option section for on
; # and off
; volume = ignore | merge | off | zero # What to do with this volume: ignore it, merge it into the device
; # volume slider, always set it to the lowest value possible, or always
; # set it to 0 dB (for whatever that means)
; enumeration = ignore | select # What to do with this enumeration, ignore it or make it selectable
; # via device ports. If set to 'select' you need to define an Option section
; # for each of the items you want to expose
; direction = playback | capture # Is this relevant only for playback or capture? If not set this will implicitly be
; # set the direction of the PCM device is opened as. Generally this doesn't need to be set
; # unless you have a broken driver that has playback controls marked for capture or vice
; # versa
; direction-try-other = no | yes # If the element does not supported what is requested, try the other direction, too?
;
; override-map.1 = ... # Override the channel mask of the mixer control if the control only exposes a single channel
; override-map.2 = ... # Override the channel masks of the mixer control if the control only exposes two channels
; # Override maps should list for each element channel which high-level channels it controls via a
; # channel mask. A channel mask may either be the name of a single channel, or the words "all-left",
; # "all-right", "all-center", "all-front", "all-rear", and "all" to encode a specific subset of
; # channels in a mask
[Element PCM]
switch = mute
volume = merge
override-map.1 = all
override-map.2 = all-left,all-right
[Element External Amplifier]
switch = select
[Option External Amplifier:on]
name = output-amplifier-on
priority = 10
[Option External Amplifier:off]
name = output-amplifier-off
priority = 0
[Element Bass Boost]
switch = select
[Option Bass Boost:on]
name = output-bass-boost-on
priority = 0
[Option Bass Boost:off]
name = output-bass-boost-off
priority = 10
;;; 'Analog Output'
[Element Analog Output]
enumeration = select
[Option Analog Output:Speakers]
name = output-speaker
priority = 10
[Option Analog Output:Headphones]
name = output-headphones
priority = 9
[Option Analog Output:FP Headphones]
name = output-headphones
priority = 8
|
