diff options
Diffstat (limited to 'tools/csr.c')
| -rw-r--r-- | tools/csr.c | 802 |
1 files changed, 802 insertions, 0 deletions
diff --git a/tools/csr.c b/tools/csr.c index 43ae25b0..556f13cb 100644 --- a/tools/csr.c +++ b/tools/csr.c @@ -424,38 +424,840 @@ char *csr_pskeytostr(uint16_t pskey) return "Maximum SCO links"; case CSR_PSKEY_MAX_REMOTE_MASTERS: return "Maximum remote masters"; + case CSR_PSKEY_ENABLE_MASTERY_WITH_SLAVERY: + return "Support master and slave roles simultaneously"; + case CSR_PSKEY_H_HC_FC_MAX_ACL_PKT_LEN: + return "Maximum HCI ACL packet length"; + case CSR_PSKEY_H_HC_FC_MAX_SCO_PKT_LEN: + return "Maximum HCI SCO packet length"; + case CSR_PSKEY_H_HC_FC_MAX_ACL_PKTS: + return "Maximum number of HCI ACL packets"; + case CSR_PSKEY_H_HC_FC_MAX_SCO_PKTS: + return "Maximum number of HCI SCO packets"; + case CSR_PSKEY_LC_FC_BUFFER_LOW_WATER_MARK: + return "Flow control low water mark"; + case CSR_PSKEY_LC_MAX_TX_POWER: + return "Maximum transmit power"; + case CSR_PSKEY_TX_GAIN_RAMP: + return "Transmit gain ramp rate"; + case CSR_PSKEY_LC_PEER_POWER_PERIOD: + return "Peer transmit power control interval"; + case CSR_PSKEY_LC_FC_POOLS_LOW_WATER_MARK: + return "Flow control pool low water mark"; + case CSR_PSKEY_LC_DEFAULT_TX_POWER: + return "Default transmit power"; + case CSR_PSKEY_LC_RSSI_GOLDEN_RANGE: + return "RSSI at bottom of golden receive range"; + case CSR_PSKEY_LC_COMBO_DISABLE_PIO_MASK: + return "Combo: PIO lines and logic to disable transmit"; + case CSR_PSKEY_LC_COMBO_PRIORITY_PIO_MASK: + return "Combo: priority activity PIO lines and logic"; + case CSR_PSKEY_LC_COMBO_DOT11_CHANNEL_PIO_BASE: + return "Combo: 802.11b channel number base PIO line"; + case CSR_PSKEY_LC_COMBO_DOT11_BLOCK_CHANNELS: + return "Combo: channels to block either side of 802.11b"; + case CSR_PSKEY_LC_MAX_TX_POWER_NO_RSSI: + return "Maximum transmit power when peer has no RSSI"; + case CSR_PSKEY_LC_CONNECTION_RX_WINDOW: + return "Receive window size during connections"; + case CSR_PSKEY_LC_COMBO_DOT11_TX_PROTECTION_MODE: + return "Combo: which TX packets shall we protect"; + case CSR_PSKEY_LC_ENHANCED_POWER_TABLE: + return "Radio power table"; + case CSR_PSKEY_LC_WIDEBAND_RSSI_CONFIG: + return "RSSI configuration for use with wideband RSSI"; + case CSR_PSKEY_LC_COMBO_DOT11_PRIORITY_LEAD: + return "Combo: How much notice will we give the Combo Card"; + case CSR_PSKEY_BT_CLOCK_INIT: + return "Initial value of Bluetooth clock"; + case CSR_PSKEY_TX_MR_MOD_DELAY: + return "TX Mod delay"; + case CSR_PSKEY_RX_MR_SYNC_TIMING: + return "RX MR Sync Timing"; + case CSR_PSKEY_RX_MR_SYNC_CONFIG: + return "RX MR Sync Configuration"; + case CSR_PSKEY_LC_LOST_SYNC_SLOTS: + return "Time in ms for lost sync in low power modes"; + case CSR_PSKEY_RX_MR_SAMP_CONFIG: + return "RX MR Sync Configuration"; + case CSR_PSKEY_AGC_HYST_LEVELS: + return "AGC hysteresis levels"; + case CSR_PSKEY_RX_LEVEL_LOW_SIGNAL: + return "ANA_RX_LVL at low signal strengths"; + case CSR_PSKEY_AGC_IQ_LVL_VALUES: + return "ANA_IQ_LVL values for AGC algorithmn"; + case CSR_PSKEY_MR_FTRIM_OFFSET_12DB: + return "ANA_RX_FTRIM offset when using 12 dB IF atten "; + case CSR_PSKEY_MR_FTRIM_OFFSET_6DB: + return "ANA_RX_FTRIM offset when using 6 dB IF atten "; + case CSR_PSKEY_NO_CAL_ON_BOOT: + return "Do not calibrate radio on boot"; + case CSR_PSKEY_RSSI_HI_TARGET: + return "RSSI high target"; + case CSR_PSKEY_PREFERRED_MIN_ATTENUATION: + return "Preferred minimum attenuator setting"; + case CSR_PSKEY_LC_COMBO_DOT11_PRIORITY_OVERRIDE: + return "Combo: Treat all packets as high priority"; + case CSR_PSKEY_LC_MULTISLOT_HOLDOFF: + return "Time till single slot packets are used for resync"; + case CSR_PSKEY_FREE_KEY_PIGEON_HOLE: + return "Link key store bitfield"; + case CSR_PSKEY_LINK_KEY_BD_ADDR0: + return "Bluetooth address + link key 0"; + case CSR_PSKEY_LINK_KEY_BD_ADDR1: + return "Bluetooth address + link key 1"; + case CSR_PSKEY_LINK_KEY_BD_ADDR2: + return "Bluetooth address + link key 2"; + case CSR_PSKEY_LINK_KEY_BD_ADDR3: + return "Bluetooth address + link key 3"; + case CSR_PSKEY_LINK_KEY_BD_ADDR4: + return "Bluetooth address + link key 4"; + case CSR_PSKEY_LINK_KEY_BD_ADDR5: + return "Bluetooth address + link key 5"; + case CSR_PSKEY_LINK_KEY_BD_ADDR6: + return "Bluetooth address + link key 6"; + case CSR_PSKEY_LINK_KEY_BD_ADDR7: + return "Bluetooth address + link key 7"; + case CSR_PSKEY_LINK_KEY_BD_ADDR8: + return "Bluetooth address + link key 8"; + case CSR_PSKEY_LINK_KEY_BD_ADDR9: + return "Bluetooth address + link key 9"; + case CSR_PSKEY_LINK_KEY_BD_ADDR10: + return "Bluetooth address + link key 10"; + case CSR_PSKEY_LINK_KEY_BD_ADDR11: + return "Bluetooth address + link key 11"; + case CSR_PSKEY_LINK_KEY_BD_ADDR12: + return "Bluetooth address + link key 12"; + case CSR_PSKEY_LINK_KEY_BD_ADDR13: + return "Bluetooth address + link key 13"; + case CSR_PSKEY_LINK_KEY_BD_ADDR14: + return "Bluetooth address + link key 14"; + case CSR_PSKEY_LINK_KEY_BD_ADDR15: + return "Bluetooth address + link key 15"; case CSR_PSKEY_ENC_KEY_LMIN: return "Minimum encryption key length"; case CSR_PSKEY_ENC_KEY_LMAX: return "Maximum encryption key length"; case CSR_PSKEY_LOCAL_SUPPORTED_FEATURES: return "Local supported features block"; + case CSR_PSKEY_LM_USE_UNIT_KEY: + return "Allow use of unit key for authentication?"; + case CSR_PSKEY_HCI_NOP_DISABLE: + return "Disable the HCI Command_Status event on boot"; + case CSR_PSKEY_LM_MAX_EVENT_FILTERS: + return "Maximum number of event filters"; + case CSR_PSKEY_LM_TEST_SEND_ACCEPTED_TWICE: + return "LM sends two LMP_accepted messages in test mode"; + case CSR_PSKEY_LM_MAX_PAGE_HOLD_TIME: + return "Maximum time we hold a device around page"; + case CSR_PSKEY_AFH_ADAPTATION_RESPONSE_TIME: + return "LM period for AFH adaption"; + case CSR_PSKEY_AFH_OPTIONS: + return "Options to configure AFH"; + case CSR_PSKEY_AFH_RSSI_RUN_PERIOD: + return "AFH RSSI reading period"; + case CSR_PSKEY_AFH_REENABLE_CHANNEL_TIME: + return "AFH good channel adding time"; + case CSR_PSKEY_NO_DROP_ON_ACR_MS_FAIL: + return "Complete link if acr barge-in role switch refused"; + case CSR_PSKEY_MAX_PRIVATE_KEYS: + return "Max private link keys stored"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR0: + return "Bluetooth address + link key 0"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR1: + return "Bluetooth address + link key 1"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR2: + return "Bluetooth address + link key 2"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR3: + return "Bluetooth address + link key 3"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR4: + return "Bluetooth address + link key 4"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR5: + return "Bluetooth address + link key 5"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR6: + return "Bluetooth address + link key 6"; + case CSR_PSKEY_PRIVATE_LINK_KEY_BD_ADDR7: + return "Bluetooth address + link key 7"; case CSR_PSKEY_LOCAL_SUPPORTED_COMMANDS: return "Local supported commands"; + case CSR_PSKEY_LM_MAX_ABSENCE_INDEX: + return "Maximum absence index allowed"; + case CSR_PSKEY_DEVICE_NAME: + return "Local device's \"user friendly\" name"; + case CSR_PSKEY_AFH_RSSI_THRESHOLD: + return "AFH RSSI threshold"; + case CSR_PSKEY_LM_CASUAL_SCAN_INTERVAL: + return "Scan interval in slots for casual scanning"; + case CSR_PSKEY_AFH_MIN_MAP_CHANGE: + return "The minimum amount to change an AFH map by"; + case CSR_PSKEY_AFH_RSSI_LP_RUN_PERIOD: + return "AFH RSSI reading period when in low power mode"; case CSR_PSKEY_HCI_LMP_LOCAL_VERSION: return "The HCI and LMP version reported locally"; case CSR_PSKEY_LMP_REMOTE_VERSION: return "The LMP version reported remotely"; + case CSR_PSKEY_HOLD_ERROR_MESSAGE_NUMBER: + return "Maximum number of queued HCI Hardware Error Events"; + case CSR_PSKEY_DFU_ATTRIBUTES: + return "DFU attributes"; + case CSR_PSKEY_DFU_DETACH_TO: + return "DFU detach timeout"; + case CSR_PSKEY_DFU_TRANSFER_SIZE: + return "DFU transfer size"; + case CSR_PSKEY_DFU_ENABLE: + return "DFU enable"; + case CSR_PSKEY_DFU_LIN_REG_ENABLE: + return "Linear Regulator enabled at boot in DFU mode"; + case CSR_PSKEY_DFUENC_VMAPP_PK_MODULUS_MSB: + return "DFU encryption VM application public key MSB"; + case CSR_PSKEY_DFUENC_VMAPP_PK_MODULUS_LSB: + return "DFU encryption VM application public key LSB"; + case CSR_PSKEY_DFUENC_VMAPP_PK_M_DASH: + return "DFU encryption VM application M dash"; + case CSR_PSKEY_DFUENC_VMAPP_PK_R2N_MSB: + return "DFU encryption VM application public key R2N MSB"; + case CSR_PSKEY_DFUENC_VMAPP_PK_R2N_LSB: + return "DFU encryption VM application public key R2N LSB"; + case CSR_PSKEY_BCSP_LM_PS_BLOCK: + return "BCSP link establishment block"; + case CSR_PSKEY_HOSTIO_FC_PS_BLOCK: + return "HCI flow control block"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO0: + return "Host transport channel 0 settings (BCSP ACK"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO1: + return "Host transport channel 1 settings (BCSP-LE"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO2: + return "Host transport channel 2 settings (BCCMD"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO3: + return "Host transport channel 3 settings (HQ"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO4: + return "Host transport channel 4 settings (DM"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO5: + return "Host transport channel 5 settings (HCI CMD/EVT"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO6: + return "Host transport channel 6 settings (HCI ACL"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO7: + return "Host transport channel 7 settings (HCI SCO"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO8: + return "Host transport channel 8 settings (L2CAP"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO9: + return "Host transport channel 9 settings (RFCOMM"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO10: + return "Host transport channel 10 settings (SDP"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO11: + return "Host transport channel 11 settings (TEST"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO12: + return "Host transport channel 12 settings (DFU"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO13: + return "Host transport channel 13 settings (VM"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO14: + return "Host transport channel 14 settings"; + case CSR_PSKEY_HOSTIO_PROTOCOL_INFO15: + return "Host transport channel 15 settings"; + case CSR_PSKEY_HOSTIO_UART_RESET_TIMEOUT: + return "UART reset counter timeout"; case CSR_PSKEY_HOSTIO_USE_HCI_EXTN: return "Use hci_extn to route non-hci channels"; + case CSR_PSKEY_HOSTIO_USE_HCI_EXTN_CCFC: + return "Use command-complete flow control for hci_extn"; + case CSR_PSKEY_HOSTIO_HCI_EXTN_PAYLOAD_SIZE: + return "Maximum hci_extn payload size"; + case CSR_PSKEY_BCSP_LM_CNF_CNT_LIMIT: + return "BCSP link establishment conf message count"; case CSR_PSKEY_HOSTIO_MAP_SCO_PCM: return "Map SCO over PCM"; + case CSR_PSKEY_HOSTIO_AWKWARD_PCM_SYNC: + return "PCM interface synchronisation is difficult"; + case CSR_PSKEY_HOSTIO_BREAK_POLL_PERIOD: + return "Break poll period (microseconds"; + case CSR_PSKEY_HOSTIO_MIN_UART_HCI_SCO_SIZE: + return "Minimum SCO packet size sent to host over UART HCI"; + case CSR_PSKEY_HOSTIO_MAP_SCO_CODEC: + return "Map SCO over the built-in codec"; + case CSR_PSKEY_PCM_CVSD_TX_HI_FREQ_BOOST: + return "High frequency boost for PCM when transmitting CVSD"; + case CSR_PSKEY_PCM_CVSD_RX_HI_FREQ_BOOST: + return "High frequency boost for PCM when receiving CVSD"; + case CSR_PSKEY_PCM_CONFIG32: + return "PCM interface settings bitfields"; + case CSR_PSKEY_USE_OLD_BCSP_LE: + return "Use the old version of BCSP link establishment"; + case CSR_PSKEY_PCM_CVSD_USE_NEW_FILTER: + return "CVSD uses the new filter if available"; + case CSR_PSKEY_PCM_FORMAT: + return "PCM data format"; + case CSR_PSKEY_CODEC_OUT_GAIN: + return "Audio output gain when using built-in codec"; + case CSR_PSKEY_CODEC_IN_GAIN: + return "Audio input gain when using built-in codec"; + case CSR_PSKEY_CODEC_PIO: + return "PIO to enable when built-in codec is enabled"; + case CSR_PSKEY_PCM_LOW_JITTER_CONFIG: + return "PCM interface settings for low jitter master mode"; + case CSR_PSKEY_HOSTIO_SCO_PCM_THRESHOLDS: + return "Thresholds for SCO PCM buffers"; + case CSR_PSKEY_HOSTIO_SCO_HCI_THRESHOLDS: + return "Thresholds for SCO HCI buffers"; + case CSR_PSKEY_HOSTIO_MAP_SCO_PCM_SLOT: + return "Route SCO data to specified slot in pcm frame"; case CSR_PSKEY_UART_BAUDRATE: return "UART Baud rate"; + case CSR_PSKEY_UART_CONFIG_BCSP: + return "UART configuration when using BCSP"; + case CSR_PSKEY_UART_CONFIG_H4: + return "UART configuration when using H4"; + case CSR_PSKEY_UART_CONFIG_H5: + return "UART configuration when using H5"; + case CSR_PSKEY_UART_CONFIG_USR: + return "UART configuration when under VM control"; + case CSR_PSKEY_UART_TX_CRCS: + return "Use CRCs for BCSP or H5"; + case CSR_PSKEY_UART_ACK_TIMEOUT: + return "Acknowledgement timeout for BCSP and H5"; + case CSR_PSKEY_UART_TX_MAX_ATTEMPTS: + return "Max times to send reliable BCSP or H5 message"; + case CSR_PSKEY_UART_TX_WINDOW_SIZE: + return "Transmit window size for BCSP and H5"; + case CSR_PSKEY_UART_HOST_WAKE: + return "UART host wakeup"; + case CSR_PSKEY_HOSTIO_THROTTLE_TIMEOUT: + return "Host interface performance control."; + case CSR_PSKEY_PCM_ALWAYS_ENABLE: + return "PCM port is always enable when chip is running"; + case CSR_PSKEY_UART_HOST_WAKE_SIGNAL: + return "Signal to use for uart host wakeup protocol"; + case CSR_PSKEY_UART_CONFIG_H4DS: + return "UART configuration when using H4DS"; + case CSR_PSKEY_H4DS_WAKE_DURATION: + return "How long to spend waking the host when using H4DS"; + case CSR_PSKEY_H4DS_MAXWU: + return "Maximum number of H4DS Wake-Up messages to send"; + case CSR_PSKEY_H4DS_LE_TIMER_PERIOD: + return "H4DS Link Establishment Tsync and Tconf period"; + case CSR_PSKEY_H4DS_TWU_TIMER_PERIOD: + return "H4DS Twu timer period"; + case CSR_PSKEY_H4DS_UART_IDLE_TIMER_PERIOD: + return "H4DS Tuart_idle timer period"; case CSR_PSKEY_ANA_FTRIM: return "Crystal frequency trim"; + case CSR_PSKEY_WD_TIMEOUT: + return "Watchdog timeout (microseconds"; + case CSR_PSKEY_WD_PERIOD: + return "Watchdog period (microseconds"; case CSR_PSKEY_HOST_INTERFACE: return "Host interface"; + case CSR_PSKEY_HQ_HOST_TIMEOUT: + return "HQ host command timeout"; + case CSR_PSKEY_HQ_ACTIVE: + return "Enable host query task?"; + case CSR_PSKEY_BCCMD_SECURITY_ACTIVE: + return "Enable configuration security"; case CSR_PSKEY_ANA_FREQ: return "Crystal frequency"; + case CSR_PSKEY_PIO_PROTECT_MASK: + return "Access to PIO pins"; + case CSR_PSKEY_PMALLOC_SIZES: + return "pmalloc sizes array"; + case CSR_PSKEY_UART_BAUD_RATE: + return "UART Baud rate (pre 18"; + case CSR_PSKEY_UART_CONFIG: + return "UART configuration bitfield"; + case CSR_PSKEY_STUB: + return "Stub"; + case CSR_PSKEY_TXRX_PIO_CONTROL: + return "TX and RX PIO control"; + case CSR_PSKEY_ANA_RX_LEVEL: + return "ANA_RX_LVL register initial value"; + case CSR_PSKEY_ANA_RX_FTRIM: + return "ANA_RX_FTRIM register initial value"; + case CSR_PSKEY_PSBC_DATA_VERSION: + return "Persistent store version"; + case CSR_PSKEY_PCM0_ATTENUATION: + return "Volume control on PCM channel 0"; + case CSR_PSKEY_LO_LVL_MAX: + return "Maximum value of LO level control register"; + case CSR_PSKEY_LO_ADC_AMPL_MIN: + return "Minimum value of the LO amplitude measured on the ADC"; + case CSR_PSKEY_LO_ADC_AMPL_MAX: + return "Maximum value of the LO amplitude measured on the ADC"; + case CSR_PSKEY_IQ_TRIM_CHANNEL: + return "IQ calibration channel"; + case CSR_PSKEY_IQ_TRIM_GAIN: + return "IQ calibration gain"; + case CSR_PSKEY_TX_OFFSET_HALF_MHZ: + return "Transmit offset"; + case CSR_PSKEY_GBL_MISC_ENABLES: + return "Global miscellaneous hardware enables"; + case CSR_PSKEY_UART_SLEEP_TIMEOUT: + return "Time in ms to deep sleep if nothing received"; + case CSR_PSKEY_DEEP_SLEEP_STATE: + return "Deep sleep state usage"; + case CSR_PSKEY_IQ_ENABLE_PHASE_TRIM: + return "IQ phase enable"; + case CSR_PSKEY_HCI_HANDLE_FREEZE_PERIOD: + return "Time for which HCI handle is frozen after link removal"; + case CSR_PSKEY_MAX_FROZEN_HCI_HANDLES: + return "Maximum number of frozen HCI handles"; + case CSR_PSKEY_PAGETABLE_DESTRUCTION_DELAY: + return "Delay from freezing buf handle to deleting page table"; + case CSR_PSKEY_IQ_TRIM_PIO_SETTINGS: + return "IQ PIO settings"; + case CSR_PSKEY_USE_EXTERNAL_CLOCK: + return "Device uses an external clock"; + case CSR_PSKEY_DEEP_SLEEP_WAKE_CTS: + return "Exit deep sleep on CTS line activity"; + case CSR_PSKEY_FC_HC2H_FLUSH_DELAY: + return "Delay from disconnect to flushing HC->H FC tokens"; + case CSR_PSKEY_RX_HIGHSIDE: + return "Disable the HIGHSIDE bit in ANA_CONFIG"; + case CSR_PSKEY_TX_PRE_LVL: + return "TX pre-amplifier level"; + case CSR_PSKEY_RX_SINGLE_ENDED: + return "RX single ended"; + case CSR_PSKEY_TX_FILTER_CONFIG: + return "TX filter configuration"; + case CSR_PSKEY_CLOCK_REQUEST_ENABLE: + return "External clock request enable"; + case CSR_PSKEY_RX_MIN_ATTEN: + return "Minimum attenuation allowed for receiver"; + case CSR_PSKEY_XTAL_TARGET_AMPLITUDE: + return "Crystal target amplitude"; + case CSR_PSKEY_PCM_MIN_CPU_CLOCK: + return "Minimum CPU clock speed with PCM port running"; + case CSR_PSKEY_HOST_INTERFACE_PIO_USB: + return "USB host interface selection PIO line"; + case CSR_PSKEY_CPU_IDLE_MODE: + return "CPU idle mode when radio is active"; + case CSR_PSKEY_DEEP_SLEEP_CLEAR_RTS: + return "Deep sleep clears the UART RTS line"; + case CSR_PSKEY_RF_RESONANCE_TRIM: + return "Frequency trim for IQ and LNA resonant circuits"; + case CSR_PSKEY_DEEP_SLEEP_PIO_WAKE: + return "PIO line to wake the chip from deep sleep"; + case CSR_PSKEY_DRAIN_BORE_TIMERS: + return "Energy consumption measurement settings"; + case CSR_PSKEY_DRAIN_TX_POWER_BASE: + return "Energy consumption measurement settings"; + case CSR_PSKEY_MODULE_ID: + return "Module serial number"; + case CSR_PSKEY_MODULE_DESIGN: + return "Module design ID"; + case CSR_PSKEY_MODULE_SECURITY_CODE: + return "Module security code"; + case CSR_PSKEY_VM_DISABLE: + return "VM disable"; + case CSR_PSKEY_MOD_MANUF0: + return "Module manufactuer data 0"; + case CSR_PSKEY_MOD_MANUF1: + return "Module manufactuer data 1"; + case CSR_PSKEY_MOD_MANUF2: + return "Module manufactuer data 2"; + case CSR_PSKEY_MOD_MANUF3: + return "Module manufactuer data 3"; + case CSR_PSKEY_MOD_MANUF4: + return "Module manufactuer data 4"; + case CSR_PSKEY_MOD_MANUF5: + return "Module manufactuer data 5"; + case CSR_PSKEY_MOD_MANUF6: + return "Module manufactuer data 6"; + case CSR_PSKEY_MOD_MANUF7: + return "Module manufactuer data 7"; + case CSR_PSKEY_MOD_MANUF8: + return "Module manufactuer data 8"; + case CSR_PSKEY_MOD_MANUF9: + return "Module manufactuer data 9"; + case CSR_PSKEY_DUT_VM_DISABLE: + return "VM disable when entering radiotest modes"; + case CSR_PSKEY_USR0: + return "User configuration data 0"; + case CSR_PSKEY_USR1: + return "User configuration data 1"; + case CSR_PSKEY_USR2: + return "User configuration data 2"; + case CSR_PSKEY_USR3: + return "User configuration data 3"; + case CSR_PSKEY_USR4: + return "User configuration data 4"; + case CSR_PSKEY_USR5: + return "User configuration data 5"; + case CSR_PSKEY_USR6: + return "User configuration data 6"; + case CSR_PSKEY_USR7: + return "User configuration data 7"; + case CSR_PSKEY_USR8: + return "User configuration data 8"; + case CSR_PSKEY_USR9: + return "User configuration data 9"; + case CSR_PSKEY_USR10: + return "User configuration data 10"; + case CSR_PSKEY_USR11: + return "User configuration data 11"; + case CSR_PSKEY_USR12: + return "User configuration data 12"; + case CSR_PSKEY_USR13: + return "User configuration data 13"; + case CSR_PSKEY_USR14: + return "User configuration data 14"; + case CSR_PSKEY_USR15: + return "User configuration data 15"; + case CSR_PSKEY_USR16: + return "User configuration data 16"; + case CSR_PSKEY_USR17: + return "User configuration data 17"; + case CSR_PSKEY_USR18: + return "User configuration data 18"; + case CSR_PSKEY_USR19: + return "User configuration data 19"; + case CSR_PSKEY_USR20: + return "User configuration data 20"; + case CSR_PSKEY_USR21: + return "User configuration data 21"; + case CSR_PSKEY_USR22: + return "User configuration data 22"; + case CSR_PSKEY_USR23: + return "User configuration data 23"; + case CSR_PSKEY_USR24: + return "User configuration data 24"; + case CSR_PSKEY_USR25: + return "User configuration data 25"; + case CSR_PSKEY_USR26: + return "User configuration data 26"; + case CSR_PSKEY_USR27: + return "User configuration data 27"; + case CSR_PSKEY_USR28: + return "User configuration data 28"; + case CSR_PSKEY_USR29: + return "User configuration data 29"; + case CSR_PSKEY_USR30: + return "User configuration data 30"; + case CSR_PSKEY_USR31: + return "User configuration data 31"; + case CSR_PSKEY_USR32: + return "User configuration data 32"; + case CSR_PSKEY_USR33: + return "User configuration data 33"; + case CSR_PSKEY_USR34: + return "User configuration data 34"; + case CSR_PSKEY_USR35: + return "User configuration data 35"; + case CSR_PSKEY_USR36: + return "User configuration data 36"; + case CSR_PSKEY_USR37: + return "User configuration data 37"; + case CSR_PSKEY_USR38: + return "User configuration data 38"; + case CSR_PSKEY_USR39: + return "User configuration data 39"; + case CSR_PSKEY_USR40: + return "User configuration data 40"; + case CSR_PSKEY_USR41: + return "User configuration data 41"; + case CSR_PSKEY_USR42: + return "User configuration data 42"; + case CSR_PSKEY_USR43: + return "User configuration data 43"; + case CSR_PSKEY_USR44: + return "User configuration data 44"; + case CSR_PSKEY_USR45: + return "User configuration data 45"; + case CSR_PSKEY_USR46: + return "User configuration data 46"; + case CSR_PSKEY_USR47: + return "User configuration data 47"; + case CSR_PSKEY_USR48: + return "User configuration data 48"; + case CSR_PSKEY_USR49: + return "User configuration data 49"; + case CSR_PSKEY_USB_VERSION: + return "USB specification version number"; + case CSR_PSKEY_USB_DEVICE_CLASS_CODES: + return "USB device class codes"; case CSR_PSKEY_USB_VENDOR_ID: return "USB vendor identifier"; case CSR_PSKEY_USB_PRODUCT_ID: return "USB product identifier"; + case CSR_PSKEY_USB_MANUF_STRING: + return "USB manufacturer string"; + case CSR_PSKEY_USB_PRODUCT_STRING: + return "USB product string"; + case CSR_PSKEY_USB_SERIAL_NUMBER_STRING: + return "USB serial number string"; + case CSR_PSKEY_USB_CONFIG_STRING: + return "USB configuration string"; + case CSR_PSKEY_USB_ATTRIBUTES: + return "USB attributes bitmap"; + case CSR_PSKEY_USB_MAX_POWER: + return "USB device maximum power consumption"; + case CSR_PSKEY_USB_BT_IF_CLASS_CODES: + return "USB Bluetooth interface class codes"; + case CSR_PSKEY_USB_LANGID: + return "USB language strings supported"; + case CSR_PSKEY_USB_DFU_CLASS_CODES: + return "USB DFU class codes block"; case CSR_PSKEY_USB_DFU_PRODUCT_ID: return "USB DFU product ID"; + case CSR_PSKEY_USB_PIO_DETACH: + return "USB detach/attach PIO line"; + case CSR_PSKEY_USB_PIO_WAKEUP: + return "USB wakeup PIO line"; + case CSR_PSKEY_USB_PIO_PULLUP: + return "USB D+ pullup PIO line"; + case CSR_PSKEY_USB_PIO_VBUS: + return "USB VBus detection PIO Line"; + case CSR_PSKEY_USB_PIO_WAKE_TIMEOUT: + return "Timeout for assertion of USB PIO wake signal"; + case CSR_PSKEY_USB_PIO_RESUME: + return "PIO signal used in place of bus resume"; + case CSR_PSKEY_USB_BT_SCO_IF_CLASS_CODES: + return "USB Bluetooth SCO interface class codes"; + case CSR_PSKEY_USB_SUSPEND_PIO_LEVEL: + return "USB PIO levels to set when suspended"; + case CSR_PSKEY_USB_SUSPEND_PIO_DIR: + return "USB PIO I/O directions to set when suspended"; + case CSR_PSKEY_USB_SUSPEND_PIO_MASK: + return "USB PIO lines to be set forcibly in suspend"; + case CSR_PSKEY_USB_ENDPOINT_0_MAX_PACKET_SIZE: + return "The maxmimum packet size for USB endpoint 0"; + case CSR_PSKEY_USB_CONFIG: + return "USB config params for new chips (>bc2"; + case CSR_PSKEY_RADIOTEST_ATTEN_INIT: + return "Radio test initial attenuator"; + case CSR_PSKEY_RADIOTEST_FIRST_TRIM_TIME: + return "IQ first calibration period in test"; + case CSR_PSKEY_RADIOTEST_SUBSEQUENT_TRIM_TIME: + return "IQ subsequent calibration period in test"; + case CSR_PSKEY_RADIOTEST_LO_LVL_TRIM_ENABLE: + return "LO_LVL calibration enable"; + case CSR_PSKEY_RADIOTEST_DISABLE_MODULATION: + return "Disable modulation during radiotest transmissions"; + case CSR_PSKEY_RFCOMM_FCON_THRESHOLD: + return "RFCOMM aggregate flow control on threshold"; + case CSR_PSKEY_RFCOMM_FCOFF_THRESHOLD: + return "RFCOMM aggregate flow control off threshold"; + case CSR_PSKEY_IPV6_STATIC_ADDR: + return "Static IPv6 address"; + case CSR_PSKEY_IPV4_STATIC_ADDR: + return "Static IPv4 address"; + case CSR_PSKEY_IPV6_STATIC_PREFIX_LEN: + return "Static IPv6 prefix length"; + case CSR_PSKEY_IPV6_STATIC_ROUTER_ADDR: + return "Static IPv6 router address"; + case CSR_PSKEY_IPV4_STATIC_SUBNET_MASK: + return "Static IPv4 subnet mask"; + case CSR_PSKEY_IPV4_STATIC_ROUTER_ADDR: + return "Static IPv4 router address"; + case CSR_PSKEY_MDNS_NAME: + return "Multicast DNS name"; + case CSR_PSKEY_FIXED_PIN: + return "Fixed PIN"; + case CSR_PSKEY_MDNS_PORT: + return "Multicast DNS port"; + case CSR_PSKEY_MDNS_TTL: + return "Multicast DNS TTL"; + case CSR_PSKEY_MDNS_IPV4_ADDR: + return "Multicast DNS IPv4 address"; + case CSR_PSKEY_ARP_CACHE_TIMEOUT: + return "ARP cache timeout"; + case CSR_PSKEY_HFP_POWER_TABLE: + return "HFP power table"; + case CSR_PSKEY_DRAIN_BORE_TIMER_COUNTERS: + return "Energy consumption estimation timer counters"; + case CSR_PSKEY_DRAIN_BORE_COUNTERS: + return "Energy consumption estimation counters"; + case CSR_PSKEY_LOOP_FILTER_TRIM: + return "Trim value to optimise loop filter"; + case CSR_PSKEY_DRAIN_BORE_CURRENT_PEAK: + return "Energy consumption estimation current peak"; + case CSR_PSKEY_FORCE_16MHZ_REF_PIO: + return "PIO line to force 16 MHz reference to be assumed"; + case CSR_PSKEY_CDMA_LO_REF_LIMITS: + return "Local oscillator frequency reference limits for CDMA"; + case CSR_PSKEY_CDMA_LO_ERROR_LIMITS: + return "Local oscillator frequency error limits for CDMA"; + case CSR_PSKEY_CLOCK_STARTUP_DELAY: + return "Clock startup delay in milliseconds"; + case CSR_PSKEY_DEEP_SLEEP_CORRECTION_FACTOR: + return "Deep sleep clock correction factor"; + case CSR_PSKEY_TEMPERATURE_CALIBRATION: + return "Temperature in deg C for a given internal setting"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_INTERNAL_PA: + return "Temperature for given internal PA adjustment"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_PRE_LVL: + return "Temperature for a given TX_PRE_LVL adjustment"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_BB: + return "Temperature for a given TX_BB adjustment"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_ANA_FTRIM: + return "Temperature for given crystal trim adjustment"; + case CSR_PSKEY_TEST_DELTA_OFFSET: + return "Frequency offset applied to synthesiser in test mode"; + case CSR_PSKEY_RX_DYNAMIC_LVL_OFFSET: + return "Receiver dynamic level offset depending on channel"; + case CSR_PSKEY_TEST_FORCE_OFFSET: + return "Force use of exact value in PSKEY_TEST_DELTA_OFFSET"; + case CSR_PSKEY_RF_TRAP_BAD_DIVISION_RATIOS: + return "Trap bad division ratios in radio frequency tables"; + case CSR_PSKEY_RADIOTEST_CDMA_LO_REF_LIMITS: + return "LO frequency reference limits for CDMA in radiotest"; case CSR_PSKEY_INITIAL_BOOTMODE: return "Initial device bootmode"; + case CSR_PSKEY_ONCHIP_HCI_CLIENT: + return "HCI traffic routed internally"; + case CSR_PSKEY_RX_ATTEN_BACKOFF: + return "Receiver attenuation back-off"; + case CSR_PSKEY_RX_ATTEN_UPDATE_RATE: + return "Receiver attenuation update rate"; + case CSR_PSKEY_SYNTH_TXRX_THRESHOLDS: + return "Local oscillator tuning voltage limits for tx and rx"; + case CSR_PSKEY_MIN_WAIT_STATES: + return "Flash wait state indicator"; + case CSR_PSKEY_RSSI_CORRECTION: + return "RSSI correction factor."; + case CSR_PSKEY_SCHED_THROTTLE_TIMEOUT: + return "Scheduler performance control."; + case CSR_PSKEY_DEEP_SLEEP_USE_EXTERNAL_CLOCK: + return "Deep sleep uses external 32 kHz clock source"; + case CSR_PSKEY_TRIM_RADIO_FILTERS: + return "Trim rx and tx radio filters if true."; + case CSR_PSKEY_TRANSMIT_OFFSET: + return "Transmit offset in units of 62.5 kHz"; + case CSR_PSKEY_USB_VM_CONTROL: + return "VM application will supply USB descriptors"; + case CSR_PSKEY_MR_ANA_RX_FTRIM: + return "Medium rate value for the ANA_RX_FTRIM register"; + case CSR_PSKEY_I2C_CONFIG: + return "I2C configuration"; + case CSR_PSKEY_MR_TX_FILTER_CONFIG: + return "TX filter configuration used for enhanced data rate"; + case CSR_PSKEY_MR_TX_CONFIG2: + return "TX filter configuration used for enhanced data rate"; + case CSR_PSKEY_USB_DONT_RESET_BOOTMODE_ON_HOST_RESET: + return "Don't reset bootmode if USB host resets"; + case CSR_PSKEY_LC_USE_THROTTLING: + return "Adjust packet selection on packet error rate"; + case CSR_PSKEY_CHARGER_TRIM: + return "Trim value for the current charger"; + case CSR_PSKEY_CLOCK_REQUEST_FEATURES: + return "Clock request is tristated if enabled"; + case CSR_PSKEY_TRANSMIT_OFFSET_CLASS1: + return "Transmit offset / 62.5 kHz for class 1 radios"; + case CSR_PSKEY_TX_AVOID_PA_CLASS1_PIO: + return "PIO line asserted in class1 operation to avoid PA"; + case CSR_PSKEY_MR_PIO_CONFIG: + return "PIO line asserted in class1 operation to avoid PA"; + case CSR_PSKEY_UART_CONFIG2: + return "The UART Sampling point"; + case CSR_PSKEY_CLASS1_IQ_LVL: + return "IQ demand level for class 1 power level"; + case CSR_PSKEY_CLASS1_TX_CONFIG2: + return "TX filter configuration used for class 1 tx power"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_INTERNAL_PA_CLASS1: + return "Temperature for given internal PA adjustment"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_EXTERNAL_PA_CLASS1: + return "Temperature for given internal PA adjustment"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_PRE_LVL_MR: + return "Temperature adjustment for TX_PRE_LVL in EDR"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_BB_MR_HEADER: + return "Temperature for a given TX_BB in EDR header"; + case CSR_PSKEY_TEMPERATURE_VS_DELTA_TX_BB_MR_PAYLOAD: + return "Temperature for a given TX_BB in EDR payload"; + case CSR_PSKEY_RX_MR_EQ_TAPS: + return "Adjust receiver configuration for EDR"; + case CSR_PSKEY_TX_PRE_LVL_CLASS1: + return "TX pre-amplifier level in class 1 operation"; + case CSR_PSKEY_ANALOGUE_ATTENUATOR: + return "TX analogue attenuator setting"; + case CSR_PSKEY_MR_RX_FILTER_TRIM: + return "Trim for receiver used in EDR."; + case CSR_PSKEY_MR_RX_FILTER_RESPONSE: + return "Filter response for receiver used in EDR."; + case CSR_PSKEY_PIO_WAKEUP_STATE: + return "PIO deep sleep wake up state "; + case CSR_PSKEY_MR_TX_IF_ATTEN_OFF_TEMP: + return "TX IF atten off temperature when using EDR."; + case CSR_PSKEY_LO_DIV_LATCH_BYPASS: + return "Bypass latch for LO dividers"; + case CSR_PSKEY_LO_VCO_STANDBY: + return "Use standby mode for the LO VCO"; + case CSR_PSKEY_SLOW_CLOCK_FILTER_SHIFT: + return "Slow clock sampling filter constant"; + case CSR_PSKEY_SLOW_CLOCK_FILTER_DIVIDER: + return "Slow clock filter fractional threshold"; + case CSR_PSKEY_USB_ATTRIBUTES_POWER: + return "USB self powered"; + case CSR_PSKEY_USB_ATTRIBUTES_WAKEUP: + return "USB responds to wake-up"; + case CSR_PSKEY_DFU_ATTRIBUTES_MANIFESTATION_TOLERANT: + return "DFU manifestation tolerant"; + case CSR_PSKEY_DFU_ATTRIBUTES_CAN_UPLOAD: + return "DFU can upload"; + case CSR_PSKEY_DFU_ATTRIBUTES_CAN_DOWNLOAD: + return "DFU can download"; + case CSR_PSKEY_UART_CONFIG_STOP_BITS: + return "UART: stop bits"; + case CSR_PSKEY_UART_CONFIG_PARITY_BIT: + return "UART: parity bit"; + case CSR_PSKEY_UART_CONFIG_FLOW_CTRL_EN: + return "UART: hardware flow control"; + case CSR_PSKEY_UART_CONFIG_RTS_AUTO_EN: + return "UART: RTS auto-enabled"; + case CSR_PSKEY_UART_CONFIG_RTS: + return "UART: RTS asserted"; + case CSR_PSKEY_UART_CONFIG_TX_ZERO_EN: + return "UART: TX zero enable"; + case CSR_PSKEY_UART_CONFIG_NON_BCSP_EN: + return "UART: enable BCSP-specific hardware"; + case CSR_PSKEY_UART_CONFIG_RX_RATE_DELAY: + return "UART: RX rate delay"; + case CSR_PSKEY_UART_SEQ_TIMEOUT: + return "UART: BCSP ack timeout"; + case CSR_PSKEY_UART_SEQ_RETRIES: + return "UART: retry limit in sequencing layer"; + case CSR_PSKEY_UART_SEQ_WINSIZE: + return "UART: BCSP transmit window size"; + case CSR_PSKEY_UART_USE_CRC_ON_TX: + return "UART: use BCSP CRCs"; + case CSR_PSKEY_UART_HOST_INITIAL_STATE: + return "UART: initial host state"; + case CSR_PSKEY_UART_HOST_ATTENTION_SPAN: + return "UART: host attention span"; + case CSR_PSKEY_UART_HOST_WAKEUP_TIME: + return "UART: host wakeup time"; + case CSR_PSKEY_UART_HOST_WAKEUP_WAIT: + return "UART: host wakeup wait"; + case CSR_PSKEY_BCSP_LM_MODE: + return "BCSP link establishment mode"; + case CSR_PSKEY_BCSP_LM_SYNC_RETRIES: + return "BCSP link establishment sync retries"; + case CSR_PSKEY_BCSP_LM_TSHY: + return "BCSP link establishment Tshy"; + case CSR_PSKEY_UART_DFU_CONFIG_STOP_BITS: + return "DFU mode UART: stop bits"; + case CSR_PSKEY_UART_DFU_CONFIG_PARITY_BIT: + return "DFU mode UART: parity bit"; + case CSR_PSKEY_UART_DFU_CONFIG_FLOW_CTRL_EN: + return "DFU mode UART: hardware flow control"; + case CSR_PSKEY_UART_DFU_CONFIG_RTS_AUTO_EN: + return "DFU mode UART: RTS auto-enabled"; + case CSR_PSKEY_UART_DFU_CONFIG_RTS: + return "DFU mode UART: RTS asserted"; + case CSR_PSKEY_UART_DFU_CONFIG_TX_ZERO_EN: + return "DFU mode UART: TX zero enable"; + case CSR_PSKEY_UART_DFU_CONFIG_NON_BCSP_EN: + return "DFU mode UART: enable BCSP-specific hardware"; + case CSR_PSKEY_UART_DFU_CONFIG_RX_RATE_DELAY: + return "DFU mode UART: RX rate delay"; + case CSR_PSKEY_AMUX_AIO0: + return "Multiplexer for AIO 0"; + case CSR_PSKEY_AMUX_AIO1: + return "Multiplexer for AIO 1"; + case CSR_PSKEY_AMUX_AIO2: + return "Multiplexer for AIO 2"; + case CSR_PSKEY_AMUX_AIO3: + return "Multiplexer for AIO 3"; + case CSR_PSKEY_LOCAL_NAME_SIMPLIFIED: + return "Local Name (simplified"; + case CSR_PSKEY_EXTENDED_STUB: + return "Extended stub"; default: return "Unknown"; } |